Skip to main content

What is transfer position in injection molding

 Friends, good morning

Aaj hum switch over position ki detail me baat karenge ki  ye kya hai aur kaise kaam karta hai

Dekhiye jab plastic melt material mold me inject ho jata hai to hum poori tarah se sure hone ke liye ki wo wapas barrel me na chala jaye aur jo impreesion hai mold me usme achche se bhar jae    uske liye hum material ko injection zone se holding zone me bhejte hai.

Holding zone me applied pressure kam rhta hai ek time rahta hai aur speed hoti hai jisme material fill hota hai behtreen tarike se.

Material ko hold karne se bahut sare defect control ho jate hai bas zaroorat hai defect ko solve karne ki

Ab transfer position jo hai wo ek aisi position hai jis par material aate hi injection zone se holding zone me chala jata hai

Agar kabhi flash ki problem aaye to hum ye position increase kar dete hai aur agar short shot aa rha ho to ye position decrease kar dete hai .

#transferposition #whatis injection molding #switchoverposition #cipet #plastic

Comments

Post a Comment

Popular posts from this blog

Types of plastic

Plastic 2 prakar ke hote hai 1 thermoplastic 2 thermosetting plastic Wo plastic jo ek baar heat dene k baad   soft ho jate hai aur easily doosrey article me convert ho jate hai .isme na unki physical property change hoti hai n chemical property change hoti bus sirf physical look change ho jata hai Jabki thermosetting plastic me  agar ek baar kisi article ko heat kiya to fir se wo dobara nhi change nhi hoga aur material degrade ho jaega aur dirty si smell aane lagti hai for example aap cooker k utensil hi lelo .isliye thermoplastics achche hote hai kyuki wo recyclable hote hai . Unse koi bahut jyada environment ka khatra bhi nhi hai . #injection molding #plastic #indiaplast #ezyplast #whatisplastic #typesofplastic #plastasia #polymer
Post a Comment
Read more

Scale callibration

 Good evening doston aur aaj ki is post Mein Main aapko scale caliberation ke bare mein bataunga scale calibration kya hoti hai jaise ki word Se Lag Raha Haicalibration  yani calibrate karna calibrate Ham Kis chij Ko karte hain use chij ko Karte Hain Jo ki Apne pahle ki avastha se bahar a chuki hai ya FIR kharab ho chuki hai to scale ka calibration Karne Wale scale Jab kharab ho jaaye ya is Khel ki jo value Hai vah disturb Ho Jaaye Kaun the scale transducer ki baat ho rahi hai yahan per to transport ki value Jab change Ho Jaati Hai To Ham use kya karte hain fir se set Karke original value Tak Lekar Aate Hain To LV DT jo hoti hai machine Mein Char Jagah per hoti hain injection unit mein yah scale main yah scale through ke movement ke liye use Hoti Hai screw ke bad FIR clamping unit mein movement ke liye kiske use Hoti Hai clamp u ke movement ke liye use hoti hai aur ek Dai Hai adjusting ke liye ek plate use Hoti Hai is tarike se Char scale jo hai vah Hoti Hai scale ko calibrate...
Post a Comment
Read more

What is suck back in injection molding

 Good morning dosto Suck back , Naam se hi lag rha hai ki koi cheez suck ho rhi hai yani kheechi ja rhi hai . Suck back ka matlab hua peeche ki taraf kheechna  .  Actually jab plastic melt material mold me inject ho jata hai aur injection ke baad holding  complete ho jati hai tab part cooling zone me jata hai aur isi waqt refilling bhi sath sath hoti rhti hai refilling poori hone k baad screw straight direction me back hota hai utne mm jitna set kiya jata hai. Alag alag material k liye alag alag value me set krte hai suck back  Suck back dene se drooling ki problem ko solve kiya jata hai aur sath hi sath   silver bhi troubleshoot hota hai .suck back dene se material me threading generate nhi hoti hai nozzle se  
Post a Comment
Read more