Skip to main content

INJECTION MOLDING DEFECT 3 ~ Black Spot

 Hello doston Aaj ham log baat karenge injection molding ke dusre defect ke bare mein Jiska Naam Hai black spot Jaisa ki aap log padh Rahe Hain Ki black spot Se Hi Lag Raha Hai Ki Aisa Nishan Jo black color ka ho ismein part mein ab Sawal yah uthata hai ki black spot Hota kya hai aur yah Kyon Aata Hai to Jaisa ki maine aap logon ko bataya ki black spot Palat ki sarface mein Kale Rang ka Nishan ya Kale Rang ka material Jab block Karta Hua aata hai Kuchh vajahon se to use hi black spot bolate Hain To Jab sabse pahle yah dhabbe yah spot spot tabhi Aate Hain Jab material melt barrel Mein degrade Ho Jaaye degrade matlab Ki Unki processing temperature Jyada hota hai to vah jal Jaate Hain varn Ho Jaate Hain material to ya FIR viral mein bahut der tak material uplabdh rahata hai jisse ki metal mein Black a jata hai material over heat Na Ho Kai bar material over heat ho jata hai jisse ki black spot sarface per Aata Hai machine Bahut Der Tak Ruki hone se material degrade ho jata hai to isliye Hamen machine ko machine ke motor ko heating off kar deni chahie barrel ke andar ke material ko degrade na hone De jection ho jayegi RPM Jyada hota hai to bhi black spot a sakta hai agar back pressure Jyada hoga tab bhi black spot a sakta hai material ko acche se Pri dry kar le Aur Ko saaf kar len hair went saaf Ho Jaega To black spot Ke Aane Ke chances kam Rahenge Main Dil jalega Nahin aur jo is group ki rotation ke time hit generate Hoti Hai vah air went se bahar ho jayegi capture Nahin Hogi jisse Van mark Nahin aaega black spot bhi nahin aaega material Mein Kuchh contamination hota hai jisse black spot Aata Hai machine ka selection mold ke hisab se sahi se karna chahie aur Jab Bhi material change ho raha ho barrel Mein To Hamen machine ko compound se viral saaf kar lena chahie kar lena chahie machine Adhik processing temperature To Nahin Hai Jyada processing temperature hoga to material ke Jalne ke chances jyada ho Jaate Hain agarwal ka residence time jyada hoga janaki material barrel me both there takrayega to medical degree ho jayega mulgi venting improper nahi honi chahiye bike racer bahut jyada nahi hona chahiye hrtc ka temperature control hona chahiye nozzle ka temperature control hona chahiye roommate railway contamination nahi honi chahiye material mein mila nahi honi chahiye milk temperature jagah hai nahi hona chahiye this for 12 mela koshish karna chahiye barrel my material component aana eating a pulling jagah nahi hai na doston yah aaj ka topic black spot Raha Humne Dekha ki Kis Tarah Se Ham plastic part Mein processing ke time black spot ko control kar lete hain Apni Taraf Se doston Aage ke block Mein Ham injection molding ke third defect ke bare mein janenge filhal ke liye Vande Mataram Jay Hind Jay Bharat aap log Mere block ko support Kariye Apna Pyar dijiye aur Jyada Se Jyada like share Kariye ummid hai aap logon ko aaj ke content Mera Pasand Aaya hoga thank u

Comments

Post a Comment

Popular posts from this blog

Types of plastic

Plastic 2 prakar ke hote hai 1 thermoplastic 2 thermosetting plastic Wo plastic jo ek baar heat dene k baad   soft ho jate hai aur easily doosrey article me convert ho jate hai .isme na unki physical property change hoti hai n chemical property change hoti bus sirf physical look change ho jata hai Jabki thermosetting plastic me  agar ek baar kisi article ko heat kiya to fir se wo dobara nhi change nhi hoga aur material degrade ho jaega aur dirty si smell aane lagti hai for example aap cooker k utensil hi lelo .isliye thermoplastics achche hote hai kyuki wo recyclable hote hai . Unse koi bahut jyada environment ka khatra bhi nhi hai . #injection molding #plastic #indiaplast #ezyplast #whatisplastic #typesofplastic #plastasia #polymer
Post a Comment
Read more

Scale callibration

 Good evening doston aur aaj ki is post Mein Main aapko scale caliberation ke bare mein bataunga scale calibration kya hoti hai jaise ki word Se Lag Raha Haicalibration  yani calibrate karna calibrate Ham Kis chij Ko karte hain use chij ko Karte Hain Jo ki Apne pahle ki avastha se bahar a chuki hai ya FIR kharab ho chuki hai to scale ka calibration Karne Wale scale Jab kharab ho jaaye ya is Khel ki jo value Hai vah disturb Ho Jaaye Kaun the scale transducer ki baat ho rahi hai yahan per to transport ki value Jab change Ho Jaati Hai To Ham use kya karte hain fir se set Karke original value Tak Lekar Aate Hain To LV DT jo hoti hai machine Mein Char Jagah per hoti hain injection unit mein yah scale main yah scale through ke movement ke liye use Hoti Hai screw ke bad FIR clamping unit mein movement ke liye kiske use Hoti Hai clamp u ke movement ke liye use hoti hai aur ek Dai Hai adjusting ke liye ek plate use Hoti Hai is tarike se Char scale jo hai vah Hoti Hai scale ko calibrate...
Post a Comment
Read more

What is suck back in injection molding

 Good morning dosto Suck back , Naam se hi lag rha hai ki koi cheez suck ho rhi hai yani kheechi ja rhi hai . Suck back ka matlab hua peeche ki taraf kheechna  .  Actually jab plastic melt material mold me inject ho jata hai aur injection ke baad holding  complete ho jati hai tab part cooling zone me jata hai aur isi waqt refilling bhi sath sath hoti rhti hai refilling poori hone k baad screw straight direction me back hota hai utne mm jitna set kiya jata hai. Alag alag material k liye alag alag value me set krte hai suck back  Suck back dene se drooling ki problem ko solve kiya jata hai aur sath hi sath   silver bhi troubleshoot hota hai .suck back dene se material me threading generate nhi hoti hai nozzle se  
Post a Comment
Read more